Design by travishumphery · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Key Insert Holder Card
Key Insert Holder Card design listed for 2018 Suzuki Swift. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Suzuki
- Model
- Swift
- Year range
- 2018
- Submodel
- Sport
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
My previous car had a thick credit card sized wireless key, so figured I could make the same for the Swift once I realised the wireless insert inside the plastic keyfob housing could easily be removed when splitting the fob open to change the battery.
Dimensions are about that of a business card (90mm x 55mm), and it is 8mm thick.
I have tried making it a bit thinner, however it makes the insert sit out and is no longer flush. I also thought about making a lid that slides over the top, however this will make it even thicker.
The keyfob insert fits in quite easily, and while it doesn't stick or click in, it sits fine and is easy enough to remove (although I have a thin piece of double sided tape at the bottom as I shouldn't ever need to remove it).
There are two versions - one just fits the insert in the middle, the second has it at the bottom left as there is a hole on the right side to insert the emergency key.
You'll need a wallet with a section thick enough for it though (I keep it with my business cards as you can see in the photo). Please note this will not work in a wallet that has RFID shielding.
Source description, under the recorded CC-BY-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 1b566b46-087c-47b7-a583-7dce5afbb774
- Part Name
- Key Insert Holder Card
- Slug
- key-insert-holder-card
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Suzuki
- Model
- Swift
- Year
- 2018
- Year End
- Not supplied
- Submodel
- Sport
- Engine
- Not supplied
- Created At
- 2026-05-10T18:17:06.49934+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:5223724
- Source Creator Url
- https://www.thingiverse.com/travishumphery
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/1b566b46-087c-47b7-a583-7dce5afbb774/images/key-insert-holder-card-1_1778437027694_wssxpj.jpg
- Author
- travishumphery
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2018/Suzuki/Swift/key-insert-holder-card
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.