Design by drunken_prozac · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Mobile Phone Mount RHD
Mobile Phone Mount RHD design listed for 2007–2014 Ford Mondeo. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Ford
- Model
- Mondeo
- Year range
- 2007–2014
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
As I had the 'power' start button my trim was all one piece so I decided to design my first thing!
It does involve opening the dash a little but this was to stop it from sliding out, I managed to do it but pulling the start button edge trim off and gently unscrewing the 2 screws behind just enough to lean the dashboard forward slightly.
Made the base of the ball a little thicker and even though the right side (bottom when printing) of the ball didn't print perfectly it still works well.
Add a little black foam pad beneath the bottom support to stop it scratching the dash.
Printing:
***Print in ABS, the PLA went soft in the summer and drooped, ABS has been fine the past year***
Printed in Black PLA as ABS just kept warping and causing the ball to fail.
100% infill for strength
Support from buildplate
I used a raft due to the small edges slightly curling off the bed but not required.
Source description, under the recorded CC-BY-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $28.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $29.00 | General-purpose candidate; heat and creep need review. |
| ASA | $32.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $31.50 | Enclosed printing; review application and dimensions. |
| TPU | $37.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $37.50 | Moisture, tolerances and application require review. |
| PA-CF | $42.50 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 23115403-a770-49e7-b41a-a8c06105806c
- Part Name
- Mobile Phone Mount RHD
- Slug
- mobile-phone-mount-rhd
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Ford
- Model
- Mondeo
- Year
- 2007
- Year End
- 2014
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-07-08T12:06:19.200153+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:4963289
- Source Creator Url
- https://www.thingiverse.com/drunken_prozac
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/23115403-a770-49e7-b41a-a8c06105806c/images/mobile-phone-mount-rhd-1_1783512379864_he39iv.jpg
- Author
- drunken_prozac
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2007-2014/Ford/Mondeo/mobile-phone-mount-rhd
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.