Design by bigwig22 · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Cup Holder Adapter
Cup Holder Adapter design listed for 2008–2011 Subaru Impreza. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Subaru
- Model
- Impreza
- Year range
- 2008–2011
- Submodel
- 2.5i, WRX
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
Seriously, I always end up spilling anything I put in my Impreza cup holder.. it's too big to fit normal soda cans so they always swinging around when i drive. I made up these little rings so it fits perfectly.
In my car, the front hole was a little bigger then the rear one so I made it 0.5mm bigger. I don't know if it's the case for everyone.
This should fit any Impreza 2008 to 2011 Sedan. (2.5i and WRX. Not sure about STi.Tell me if you ever try it) It could fit many Subary car between these years, i'm not sure about other models, let me know if you try.
Enjoy!
Source description, under the recorded CC-BY-4.0 license.
Print instructions
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 25f7733c-88e3-4b91-a5b6-4630100ff639
- Part Name
- Cup Holder Adapter
- Slug
- cup-holder-adapter
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Subaru
- Model
- Impreza
- Year
- 2008
- Year End
- 2011
- Submodel
- 2.5i, WRX
- Engine
- Not supplied
- Created At
- 2026-05-03T04:31:05.192596+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:1623334
- Source Creator Url
- https://www.thingiverse.com/bigwig22
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/25f7733c-88e3-4b91-a5b6-4630100ff639/images/cup-holder-adapter-1_1777782669505_m4wdzg.jpg
- Author
- bigwig22
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2008-2011/Subaru/Impreza/cup-holder-adapter
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.