Design by osunick · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Rear Cupholder
Rear Cupholder design listed for 1964 Porsche 911. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Porsche
- Model
- 911
- Year range
- 1964
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
1. Remove rubber mat on bottom of rear bin
2. Under this mat, there is a plastic door, remove it.
3. Remove nut under door.
4. Print cupholder
5. Insert cupholder and secure with nut
6. Cover nut with cap
Cup holder is at 4 degree angle so that the holder sits level with the ground. Diameter of the cupholder is 80mm, large enough for standard Hydro Flask w/rubber bottoms but not the wide models. Optional spring insert for narrower diameter cups (TPU preferred), insert ring side down.
Cupholder liner is optional and should be printed in TPU or some other flex material.
Source description, under the recorded CC-BY-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 285b141d-829c-4b74-bbf9-f2f386e9b57e
- Part Name
- Rear Cupholder
- Slug
- rear-cupholder
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Porsche
- Model
- 911
- Year
- 1964
- Year End
- Not supplied
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-07-07T10:15:29.68917+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:4697816
- Source Creator Url
- https://www.thingiverse.com/osunick
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/285b141d-829c-4b74-bbf9-f2f386e9b57e/images/rear-cupholder-1_1783419330494_0w7t7j.jpg
- Author
- osunick
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/1964/Porsche/911/rear-cupholder
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.