Design by AleksBozovic · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Si Hood Release
Si Hood Release design listed for 1972–2026 Honda Civic. Listed category: exterior. Verify dimensions, fitment and material suitability before printing.
- Make
- Honda
- Model
- Civic
- Year range
- 1972–2026
- Submodel
- Si
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
It's designed to install without removing the trim, so conceivable the head can be as big as you want, or whatever shape you want. You install it by aligning it with the rod/shaft from the bottom, clipping it on and turning it so the meat of the handle is below (which is opposite of the direction you pull. You can also use a zip-tie (I have lots that came with the Anet printer) and if you drape the zip tie around the part when you install it, you can reach it from above (see in the photo where the bit of zip tie sticks out above) and tighten it.
I'm not a good photographer... If I make better pictures, I will post them. Plus it's an old car, difficult to make it look pristine.
My first draft broke, since the walls were thin, but this one looks OK. PLA because I print indoors and don't want to stink up the place. Orange because why not.
Source description, under the recorded CC-BY-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $28.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $29.00 | General-purpose candidate; heat and creep need review. |
| ASA | $32.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $31.50 | Enclosed printing; review application and dimensions. |
| TPU | $37.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $37.50 | Moisture, tolerances and application require review. |
| PA-CF | $42.50 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 3a1794c7-3e57-4e81-abe5-05a55294f397
- Part Name
- Si Hood Release
- Slug
- si-hood-release
- Category
- exterior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Honda
- Model
- Civic
- Year
- 1972
- Year End
- 2026
- Submodel
- Si
- Engine
- Not supplied
- Created At
- 2026-07-07T10:28:34.94547+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:3138713
- Source Creator Url
- https://www.thingiverse.com/AleksBozovic
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/3a1794c7-3e57-4e81-abe5-05a55294f397/images/si-hood-release-1_1783420115311_6ggi98.jpg
- Author
- AleksBozovic
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/1972-2026/Honda/Civic/si-hood-release
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.