Design by iywdde · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Trunk Lid Rubber Bumper Stop
Trunk Lid Rubber Bumper Stop design listed for 1989–1994 Nissan 200SX. Listed category: exterior. Verify dimensions, fitment and material suitability before printing.
- Make
- Nissan
- Model
- 200SX
- Year range
- 1989–1994
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
When fitting the rubbers, the trunk door should sit flush with the chassis once closed.
Note: If necessary, adjust the height of the lock (2 nuts) until it closes without effort and opens with just one turn of the key without having to hold it.
If the lock cannot be adjusted to open at a touch — and in some cases the trunk light stays on — it is very common for this to be caused by a nylon component inside the lock mechanism which disintegrates with age. The solution is: after removing the remains, clean and lubricate the area with lithium grease, then place a small piece of rubber inside the lock mechanism, which can be easily manipulated with pliers or a fine screwdriver to position it. In my case I cut a piece approximately 20x20mm from an old coolant hose. Afterwards, re-adjust the lock with the two nuts.
Source description, under the recorded CC-BY-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $28.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $29.00 | General-purpose candidate; heat and creep need review. |
| ASA | $32.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $31.50 | Enclosed printing; review application and dimensions. |
| TPU | $37.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $37.50 | Moisture, tolerances and application require review. |
| PA-CF | $42.50 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 3dcbafb1-e954-43fc-bd1c-35587e5452d7
- Part Name
- Trunk Lid Rubber Bumper Stop
- Slug
- trunk-lid-rubber-bumper-stop
- Category
- exterior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Nissan
- Model
- 200SX
- Year
- 1989
- Year End
- 1994
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-05-07T07:11:16.779776+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:5535359
- Source Creator Url
- https://www.thingiverse.com/iywdde
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/3dcbafb1-e954-43fc-bd1c-35587e5452d7/images/trunk-lid-rubber-bumper-stop-1_1778137877755_c3k00y.jpg
- Author
- iywdde
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/1989-1994/Nissan/200SX/trunk-lid-rubber-bumper-stop
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.