Design by MrOHaver1975 · Original design · CC-BY-SA-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Door Handle Insert Trim
Door Handle Insert Trim design listed for 2007–2011 Jeep Wrangler. Listed category: exterior. Verify dimensions, fitment and material suitability before printing.
- Make
- Jeep
- Model
- Wrangler
- Year range
- 2007–2011
- Submodel
- Rubicon
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
Next round, i plan to increase the infill so that the screws don't dig in so much, but so far they look and hold great. I took a rubber mallet to pound the letters in place once i had them seated a bit. I but them on the jeep with a piece of cardboard and vise grips so it didn't scratch anything. this held them in place while i drilled the holes that the screws go in. I had amazon bought inserts before, so i just reused the screws. I suppose you could 3M tape them in place and not drill, BUT... they would have to be heated up and bent, since the handles have a slight arc to them. I find screwing them down, bends them naturally and doesn't require extra nonsense/work. and they don't pop off magically over time. My other ones have been on for several years with no issues. through trails, creeks and mud. My Jeep theme is Storm Trooper/Dark Side. So if you love Star Wars and Jeeps like I do, then this is for you!
Source description, under the recorded CC-BY-SA-4.0 license.
Print instructions
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $28.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $29.00 | General-purpose candidate; heat and creep need review. |
| ASA | $32.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $31.50 | Enclosed printing; review application and dimensions. |
| TPU | $37.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $37.50 | Moisture, tolerances and application require review. |
| PA-CF | $42.50 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 63fc72c7-981e-47c0-bb01-14e8e270fbfa
- Part Name
- Door Handle Insert Trim
- Slug
- door-handle-insert-trim
- Category
- exterior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Jeep
- Model
- Wrangler
- Year
- 2007
- Year End
- 2011
- Submodel
- Rubicon
- Engine
- Not supplied
- Created At
- 2026-04-29T06:08:02.117006+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:7143522
- Source Creator Url
- https://www.thingiverse.com/MrOHaver1975
- Cc License Code
- CC-BY-SA-4.0
- Cc License Url
- https://creativecommons.org/licenses/by-sa/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/63fc72c7-981e-47c0-bb01-14e8e270fbfa/images/door-handle-insert-trim-1_1777442903185_5kcnzj.jpg
- Author
- MrOHaver1975
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2007-2011/Jeep/Wrangler/door-handle-insert-trim
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.