Design by renatotrede · Original design · CC-BY-SA-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Cargo Cover Tonneau Clip
Cargo Cover Tonneau Clip design listed for 2018–2025 Mitsubishi Eclipse Cross. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Mitsubishi
- Model
- Eclipse Cross
- Year range
- 2018–2025
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
This is a replacement plastic clip/retainer for the cargo cover (trunk/luggage tonneau cover) on the Mitsubishi Eclipse Cross (2018–2025).
It’s designed to hold the edge of the cargo cover in place on the vehicle’s side/support point, helping eliminate looseness, rattles, and vibration—just like the original part shown in the photos.
✅ Vehicle fitment: Mitsubishi Eclipse Cross 2018–2025 (please compare with your OEM part before printing)
✅ Purpose: secure/anchor the cargo cover (tonneau) in the trunk area
✅ Use case: replaces a broken/cracked/missing OEM plastic clip
Installation
Remove the damaged/missing clip (if still present).
Place the printed part in the same position as the OEM clip.
Fasten it the same way as the original (screw/clip-in, depending on your cargo cover).
Test fit and adjust if needed (light sanding on contact surfaces usually solves tight fits).
Print recommendations
Material: PETG (recommended) or ABS/ASA (better for heat). PLA can work but may deform in hot cars.
Infill: 40–70% (higher if you want it extra rigid)
Perimeters/Walls: 4+
Layer height: 0.2 mm
Orientation: print so the “hook/clip” area has strong layer support (avoid orientations that make the clip rely on layer adhesion alone).
Post-processing: light sanding for a perfect fit.
Notes
Modeled from an original part and measurements from my vehicle. Small variations may exist between trims/years/production batches.
If it’s too tight: sand slightly. If it’s too loose: try XY compensation in your slicer or reprint with thicker walls.
Disclaimer
This is an unofficial 3D-printed replacement part and is not affiliated with Mitsubishi. Use at your own risk.
Source description, under the recorded CC-BY-SA-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $17.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $18.00 | General-purpose candidate; heat and creep need review. |
| ASA | $18.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $18.50 | Enclosed printing; review application and dimensions. |
| TPU | $20.00 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $20.00 | Moisture, tolerances and application require review. |
| PA-CF | $21.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 6b74cac9-408f-410b-8761-557cdedd799f
- Part Name
- Cargo Cover Tonneau Clip
- Slug
- cargo-cover-tonneau-clip
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Mitsubishi
- Model
- Eclipse Cross
- Year
- 2018
- Year End
- 2025
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-05-07T07:44:39.900101+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:7301354
- Source Creator Url
- https://www.thingiverse.com/renatotrede
- Cc License Code
- CC-BY-SA-4.0
- Cc License Url
- https://creativecommons.org/licenses/by-sa/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/6b74cac9-408f-410b-8761-557cdedd799f/images/cargo-cover-tonneau-clip-1_1778139881205_58vy1e.jpg
- Author
- renatotrede
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 4
- Detail Url
- https://3dcarparts.org/library/2018-2025/Mitsubishi/Eclipse%20Cross/cargo-cover-tonneau-clip
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.