Design by geekdaddy · Original design · CC-BY-SA-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Wireless charger stand
Wireless charger stand design listed for 2022–2023 Chevrolet Bolt EUV. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Chevrolet
- Model
- Bolt EUV
- Year range
- 2022–2023
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
This version incorporates a fixed stand that can accommodate the shaft of a windshield or dashboard mounting system that comes with many popular wireless charger cradles available on amazon, ebay, aliexpress, etc. Use a hack-saw to leave behind approximately 3/8" of the shaft behind the swivel ball, and glue it into the square hole in the top of the stand. The ball on the end of the shaft snaps into the back of the wireless charger.
This design was evaluated with these cradles and the fit of the shaft was good:
https://www.amazon.com/dp/B0BL1S9LFJ
https://www.amazon.com/dp/B08D5XJTJS
Depending on the wireless charging cradle that you buy, you may have to adjust the size of the square hole in this stand -- by modifying the design or by using a file or knife to trim the printed part.
Secure the stand into the hole in the Bolt/Bolt EUV's console using high-strength 3M double sided tape affixed to the base. Chevy used this console design in Chevy Bolt EUVs and model year 22-23 Chevy Bolts
Print this with ABS or PETG. PLA is more likely to soften and deform under higher summer interior temperatures.
Source description, under the recorded CC-BY-SA-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $28.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $29.00 | General-purpose candidate; heat and creep need review. |
| ASA | $32.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $31.50 | Enclosed printing; review application and dimensions. |
| TPU | $37.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $37.50 | Moisture, tolerances and application require review. |
| PA-CF | $42.50 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 6cb23d22-6ca4-46a2-ba2b-d48e541b5381
- Part Name
- Wireless charger stand
- Slug
- wireless-charger-stand
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Chevrolet
- Model
- Bolt EUV
- Year
- 2022
- Year End
- 2023
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-07-08T11:50:03.753164+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:6580736
- Source Creator Url
- https://www.thingiverse.com/geekdaddy
- Cc License Code
- CC-BY-SA-4.0
- Cc License Url
- https://creativecommons.org/licenses/by-sa/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/6cb23d22-6ca4-46a2-ba2b-d48e541b5381/images/wireless-charger-stand-1_1783511404610_7zg59a.jpg
- Author
- geekdaddy
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2022-2023/Chevrolet/Bolt%20EUV/wireless-charger-stand
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.