Design by snu · Original design · CC0-1.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Phone Holder Adapter
Phone Holder Adapter design listed for 2015–2020 Toyota Sienna. Listed category: mounts-brackets. Verify dimensions, fitment and material suitability before printing.
- Make
- Toyota
- Model
- Sienna
- Year range
- 2015–2020
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
The mount this was designed for should fit post-refresh XL30 Siennas (2015 and newer). I've only tested it in a 2016 Sienna, but if your dashboard looks like the one in this picture, it should fit (over the right driver's side vent). https://cars.usnews.com/static/images/Auto/izmo/i960927/2016_toyota_sienna_dashboard.jpg
The holder works OK with my Kyocera Duraforce Pro 2 (pretty thick phone). I had to scale it up a bit though. If you have a thinner phone (like an iPhone with a thin case), print everything at 1x scale.
This holder slots into the right driver's side vent and limits its range of motion a bit. This hasn't been an issue for me.
The adapter may need some scaling and post-print finishing to fit right. To dial in your print settings, print the part at 1x scale with low infill (10-20%) so you don't waste too much plastic. See how it fits and adjust it accordingly, then reprint it at 50-100% infill until you get it right. If the cylindrical end doesn't fit in the dashboard bracket, use some coarse sandpaper to make it a little thinner.
Parts list:
1x Dash_mount_without_screw_hole.stl, 1x Connector_thin_curved.stl, 1x GPS_mount_main_part.stl https://www.thingiverse.com/thing:1510253
1x Gripping_Smartphone_Holder.stl (or the individual body and slide files), 1x socket.stl, 1x Threaded_Nut.stl https://www.thingiverse.com/thing:1778271
1x adapter (duh)
1x Command strip (I used the black velcro ones), 1x rubber band (a little larger than a golf ball in diameter, feel free to experiment)
Source description, under the recorded CC0-1.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- 7ccc972c-8f26-458a-ac0f-e9074bc89c7c
- Part Name
- Phone Holder Adapter
- Slug
- phone-holder-adapter
- Category
- mounts-brackets
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Toyota
- Model
- Sienna
- Year
- 2015
- Year End
- 2020
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-05-10T08:10:42.091427+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:3895793
- Source Creator Url
- https://www.thingiverse.com/snu
- Cc License Code
- CC0-1.0
- Cc License Url
- https://creativecommons.org/publicdomain/zero/1.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/7ccc972c-8f26-458a-ac0f-e9074bc89c7c/images/phone-holder-adapter-1_1778400643015_pbz8mo.jpg
- Author
- snu
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2015-2020/Toyota/Sienna/phone-holder-adapter
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.