Design by samlikedancer13 · Original design · CC-BY-SA-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Reverse Light Cover
Reverse Light Cover design listed for 1969 Dodge D200. Listed category: exterior. Verify dimensions, fitment and material suitability before printing.
- Make
- Dodge
- Model
- D200
- Year range
- 1969
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
Cura settings are as Follows (Mind you this only works for clear PETG and an ender 3)
1. Use a 0.8 nozzle. (I just used the 0.8 and used draft quality)
2. Add supports to it and make sure they are Touching Baseplate and Tree as support structure.
3. MAKE SURE YOU ABSOLUTELY CHANGE THE SIZE TO 73.2 MM IN CURA!!
4. I used skirt as the bed adhesion.
5. the infill pattern MUST BE Lines with ZERO infill line directions. (If you don't see the Infill Line Directions one then you don't have it enabled. Go to Cura Preferences and settings then find the Infill settings and look for a box that says Infill Line Directions and check it)
6. Leave everything else the same.
I put the blender stl if anyone wanted to change anything on it. I have a Photo to show you how to face it properly in Cura. Good luck to you all!!
This was my first ever commissioned 3D print and I have to say that I didn't do bad Honestly for my first time modeling.
Source description, under the recorded CC-BY-SA-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $28.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $29.00 | General-purpose candidate; heat and creep need review. |
| ASA | $32.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $31.50 | Enclosed printing; review application and dimensions. |
| TPU | $37.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $37.50 | Moisture, tolerances and application require review. |
| PA-CF | $42.50 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- b6f866c8-83e0-4324-a8e8-fe9193a64efc
- Part Name
- Reverse Light Cover
- Slug
- reverse-light-cover
- Category
- exterior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Dodge
- Model
- D200
- Year
- 1969
- Year End
- Not supplied
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-05-07T11:29:53.431135+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:6941588
- Source Creator Url
- https://www.thingiverse.com/samlikedancer13
- Cc License Code
- CC-BY-SA-4.0
- Cc License Url
- https://creativecommons.org/licenses/by-sa/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/b6f866c8-83e0-4324-a8e8-fe9193a64efc/images/reverse-light-cover-1_1778153394344_eslpc8.jpg
- Author
- samlikedancer13
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/1969/Dodge/D200/reverse-light-cover
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.