Design by rhodeseng · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Small Can holder
Small Can holder design listed for 2001–2008 Peugeot 307. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Peugeot
- Model
- 307
- Year range
- 2001–2008
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
I quickly designed this holder as I have found the holders the Peugeot 307 I have are of less than optimal usefulness (many expletives used when my can of beverage spills).
This Can holder is design to fit a 53mm Can (has a 60mm hole) and mounts in a Peugeot 307 fan ducts next to the door. It may fit other models of Peugeot (no others have been tried). It's designed so the Can will not slip though the holder even if forced at an angle.
It can be removed but it may require the use of tools to do so. The vertical blades in the vent have limited movement with this holder fitted.
Note: Not guaranteed to fit any known or unknown car. All I know is that it fits my Peugeot 307.
Note: Use at your on risk!! (meaning that I assume no responsibility for any events or problems caused by it detaching while driving or otherwise reducing your ability to driver your car safely).
Note: It's not designed to be removed easily and may cause damage to your car while trying remove it.
Update: Oct 2021
I have added the STEP AP 242 file for those that would like to hack my design. It is free for you to use as you wish. If you get rich from it, send me a nice (cold) Beer to enjoy.
Source description, under the recorded CC-BY-4.0 license.
Print instructions
It was printed on a MakerBot Replicator with the following setup:
Object infill = 20%
Layer Thickness = 0.2mm
Number of shells = 2
The "Vent_Clip.stl" part must be printed with support because it has over hangs. The other parts can be printed without support and all together.
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- ba2ccae0-919e-4c30-8a8e-29bc9ab489e6
- Part Name
- Small Can holder
- Slug
- small-can-holder
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Peugeot
- Model
- 307
- Year
- 2001
- Year End
- 2008
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-07-08T07:02:49.08549+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:120985
- Source Creator Url
- https://www.thingiverse.com/rhodeseng
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/ba2ccae0-919e-4c30-8a8e-29bc9ab489e6/images/small-can-holder-1_1783494170130_rlc6yd.jpg
- Author
- rhodeseng
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2001-2008/Peugeot/307/small-can-holder
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.