Design by chrisjfinlay · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Abarth & Cup Holder Insert
Abarth & Cup Holder Insert design listed for 2007 Fiat 500. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- Fiat
- Model
- 500
- Year range
- 2007
- Submodel
- Abarth
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
This insert fits snugly into the driver's side cup holder on the floor, and will accept a 16oz Starbucks cup with or without a cardboard collar. Your mileage may vary with other cups but I'm sure it'll work for many other drinks vessels.
The STL is oriented as intended to be installed - i.e. wider side up - and will probably print fine that way as there's no major overhangs. However for my print, I rotated it 180 around the X axis and printed it upside down.
There is still a little wobble because I didn't want to get the cup stuck, but it's the same as any other cup holder now. As the top of the holder comes up around half of the cup height, it ain't going anywhere.
If you press your cup in too hard and it DOES get stuck, a little force will remove the insert from the original holder.
Please note that this current version will block off the passenger side holder somewhat. But they have two free hands, right?
Demo of it working: https://www.youtube.com/watch?v=QBmaJMKgV8E
Example printed in Prusa Silver PLA
Source description, under the recorded CC-BY-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- d1822340-febe-4189-a86b-b4c78342509c
- Part Name
- Abarth & Cup Holder Insert
- Slug
- abarth-cup-holder-insert
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Fiat
- Model
- 500
- Year
- 2007
- Year End
- Not supplied
- Submodel
- Abarth
- Engine
- Not supplied
- Created At
- 2026-07-07T10:30:59.432286+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:3030494
- Source Creator Url
- https://www.thingiverse.com/chrisjfinlay
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/d1822340-febe-4189-a86b-b4c78342509c/images/abarth-cup-holder-insert-1_1783420260667_8xtpaq.jpg
- Author
- chrisjfinlay
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/2007/Fiat/500/abarth-cup-holder-insert
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.