Design by highvoltag3 · Original design · CC-BY-SA-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Hood Rod Holder Grommet
Hood Rod Holder Grommet design listed for 2014 Toyota Corolla. Listed category: exterior. Verify dimensions, fitment and material suitability before printing.
- Make
- Toyota
- Model
- Corolla
- Year range
- 2014
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
Source description, under the recorded CC-BY-SA-4.0 license.
Print instructions
If printing with **NinjaFlex** on an UP Mini this are the settings I used (printing NinjaFlex on an Up mini was a lot trickier than I thought).
- Extruder Temp: 259?
- Quality: Fine
- Resolution: 0.20mm
- Fill: Loose
- Raft: No raft
In an UP mini not using those setting produces, well... junk!
##Story
After I had an accident and the whole front was replaced, I kept hearing a strange sound only at about 11000RPM's, they where not able to fine any mechanical issues at the body shop nor at the dealer, everything seemed to be in place, and the noise was tricky to reproduce to say the least but quite annoying. After some trial an error I noticed that it had something to do with the Hood rod, since removing it took care of the sound, the original grommet is made of hard plastic (I suspect some sort of Nylon) and it seems like once removed it breaks and needs to be replaced, maybe they kept the original after replacing the front, any how it seemed hard enough not to grab the rod strongly though creating noise when it vibrated.
I looked for a rubber one with not much success and since I had a printer and some NinjaFlex why not make my own? :)
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- eb6beb63-39aa-461a-8a88-6522584877f9
- Part Name
- Hood Rod Holder Grommet
- Slug
- hood-rod-holder-grommet
- Category
- exterior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Toyota
- Model
- Corolla
- Year
- 2014
- Year End
- Not supplied
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-05-09T06:21:53.979913+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:603306
- Source Creator Url
- https://www.thingiverse.com/highvoltag3
- Cc License Code
- CC-BY-SA-4.0
- Cc License Url
- https://creativecommons.org/licenses/by-sa/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/eb6beb63-39aa-461a-8a88-6522584877f9/images/hood-rod-holder-grommet-1_1778307715077_ngmq89.jpg
- Author
- highvoltag3
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 2
- Detail Url
- https://3dcarparts.org/library/2014/Toyota/Corolla/hood-rod-holder-grommet
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.