Design by MakerBeck · Original design · CC-BY-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Hood Stop
Hood Stop design listed for 1993 Jeep Grand Cherokee. Listed category: exterior. Verify dimensions, fitment and material suitability before printing.
- Make
- Jeep
- Model
- Grand Cherokee
- Year range
- 1993
- Submodel
- Laredo
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
One of these parts was what I call a hood stop. There is on on either side of the front that hold the hood at the right level when it is latched. One of these had broken off and was missing so I decided to make a new one.
This is based on measurements of the original and works. It is a little tight getting it started but then goes in fine. The threads could potentially be made slightly thinner but it worked as is. I will include a STP file if anyone wants to edit it.
I printed it top side down on an Ultimaker S5 with soluble support. It is printed in ABS as I was concerned about the low glass temp of PLA. You should be able to print with break away supports also. I did 3 shells and 20% fill.
Caution: You should make your own decisions about using this under your vehicle hood.
Source description, under the recorded CC-BY-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $28.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $29.00 | General-purpose candidate; heat and creep need review. |
| ASA | $32.50 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $31.50 | Enclosed printing; review application and dimensions. |
| TPU | $37.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $37.50 | Moisture, tolerances and application require review. |
| PA-CF | $42.50 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- f6d72b66-2b87-427d-b461-0ade468d126e
- Part Name
- Hood Stop
- Slug
- hood-stop
- Category
- exterior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- Jeep
- Model
- Grand Cherokee
- Year
- 1993
- Year End
- Not supplied
- Submodel
- Laredo
- Engine
- Not supplied
- Created At
- 2026-05-06T04:50:50.022375+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:3376583
- Source Creator Url
- https://www.thingiverse.com/MakerBeck
- Cc License Code
- CC-BY-4.0
- Cc License Url
- https://creativecommons.org/licenses/by/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/f6d72b66-2b87-427d-b461-0ade468d126e/images/hood-stop-1_1778043051033_z2h0w6.jpg
- Author
- MakerBeck
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/1993/Jeep/Grand%20Cherokee/hood-stop
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.