Design by curious_pl · Original design · CC-BY-SA-4.0 · Source details. Indexed via 3DCarParts. Source text and images remain credited to their creators; no modified design files supplied.
Designer source image. It may show an installed part, prototype or render; it is not an Orphaned Parts production sample.
Vent Cup Holder
Vent Cup Holder design listed for 1996 VW Polo. Listed category: interior. Verify dimensions, fitment and material suitability before printing.
- Make
- VW
- Model
- Polo
- Year range
- 1996
- Submodel
- Not supplied
- Engine
- Not supplied
Source approval status: pending. Source flags do not certify fit, material suitability or safety for your vehicle.
License conditions, files, application and fit are reviewed before work is accepted.
Description
It fits VW polo 6n 1996 vent layout perfectly.
another remix is about higher and slimmer thermal cup, or 0.5L PET bottle . i've noticed cup and bottles designs very a lot so i've included blender file - to allow anyone adjust height of upper holder .
be carefull to not rise the upper holder too high - be certain bottle is still secured even when it's bottom falls out of bottom stand. also a little bit of rattle is better than too snug fit, as it's annoying to lift whole holder along with cup and it can waste unnessesary seconds.
Ofcourse stay safe and NEVER drink while driving! pull over, or use long timed intersection lights. @ just 50km/h you pass ~14m in 1s eye blink!
EDIT: after almost year of use i've noticed ABS-like any other rubber compound - is prone to aging due to exposure to road-borne ozone.
If you want to make your cup holder survive longer without becoming brittle , try to coat it with acrylic lacquer, and/or use better cabin filter .
Source description, under the recorded CC-BY-SA-4.0 license.
Print instructions
- Layer height: 0.2mm
- Infill: 70%
- Supports: As needed
Settings from the source; not independently tested by Orphaned Parts.
Print price estimates
Planning prices for one print, not a final quote. Defaults use a size allowance inferred from the part name, not a measured or sliced model. Filament suitability must be confirmed.
| Filament | USD / print | Application notes |
|---|---|---|
| PLA | $42.50 | Indoor prototypes; not a default material for hot vehicle interiors. |
| PETG | $43.50 | General-purpose candidate; heat and creep need review. |
| ASA | $50.00 | Candidate for UV exposure; verify temperature and geometry. |
| ABS | $48.00 | Enclosed printing; review application and dimensions. |
| TPU | $60.50 | Flexible designs only; not a substitute for rigid materials. |
| Nylon | $60.00 | Moisture, tolerances and application require review. |
| PA-CF | $69.00 | Filled nylon; abrasive filament and fit need review. |
Pricing assumptions and exclusions
USD: ($6 setup + $3 finishing + filament weight × assumed spool cost × 1.25 waste allowance + print hours × $2.50 × material time factor) ÷ 0.65. Rounded up to the next $0.50.
Assumed spool costs per kg: PLA $25, PETG $30, ASA $40, ABS $30, TPU $45, Nylon $65, PA-CF $95. Time factors: PLA/PETG 1.0, ASA/ABS 1.2, TPU 1.6, Nylon 1.4, PA-CF 1.5. These are proposed shop rates, not measured production costs.
Design work, test fitting, hardware, shipping and tax are additional where needed. Multi-file sets may need several prints. Use actual sliced weight and time when available. Final pricing is confirmed in writing.
All available source data
- Id
- f7464596-e4a2-4d66-bc05-9401425d5317
- Part Name
- Vent Cup Holder
- Slug
- vent-cup-holder
- Category
- interior
- Cswp Approval Status
- pending
- Download Status
- approved
- Make
- VW
- Model
- Polo
- Year
- 1996
- Year End
- Not supplied
- Submodel
- Not supplied
- Engine
- Not supplied
- Created At
- 2026-07-08T09:13:33.013672+00:00
- Origin
- aggregated
- Source
- thingiverse
- Source Url
- https://www.thingiverse.com/thing:334597
- Source Creator Url
- https://www.thingiverse.com/curious_pl
- Cc License Code
- CC-BY-SA-4.0
- Cc License Url
- https://creativecommons.org/licenses/by-sa/4.0/
- For Sale
- No
- Fulfillment Mode
- platform
- Manual Price Cents
- Not supplied
- Image Url
- https://r2-upload.3dcarparts.workers.dev/file/parts/f7464596-e4a2-4d66-bc05-9401425d5317/images/vent-cup-holder-1_1783502013875_213k5h.jpg
- Author
- curious_pl
- Estimated Price Cents
- Not supplied
- HasMultipleModelFiles
- No
- ModelFileCount
- 0
- Download Count
- 0
- Detail Url
- https://3dcarparts.org/library/1996/VW/Polo/vent-cup-holder
Source price fields and sale flags are metadata, not our selling prices. Their currency was not specified in the catalog. File counts do not mean files were downloaded or tested. No manufacturer savings or discontinued status is inferred.